I have a QuestionHi Doug -
My name is EJ and I found your website searching for a solution to a situation I haven't encountered installing fire alarms.
I have an auditorium that needs to have the sound shut down when the fire alarm is activated. The sound board or DSP (Digital Signal Processing) has an emergency input that I can connect to, but the prints are engineered to use the SLC loop to shut it down.
The problem is, the DSP needs 2-24 volts sent to it to shut it down.
How would this work with an SLC circuit? I think I need to use a NAC circuit to send voltage when in alarm.
Any help you could provide would be GREAT!!!!
First off, remember that the Signaling Line Circuit (SLC) is basically an extension of the Central Processing Unit in the Fire Alarm Control Panel. By itself, it does not detect fires or switch anything on or off. Instead, input modules on the SLC interpret the signals from a detector into the data sent on the SLC, and output modules interpret the data on the SLC to open or close control relay contacts.
Control relays, by themselves, do not provide any voltage or power. However, the relays can be used to switch on or off power like a light switch turns on and off power to a light bulb.
Source of PowerTo supply the 2 to 24 Volts DC for the sound board, you need power from somewhere. The trouble is this is a Life Safety Fire Alarm System being used to turn off the sound in the auditorium.
That means that the source of this 2 to 24 VDC has to be provided by a Fire Rated power supply that is monitored for trouble by the Fire Alarm Control Panel (FACP). This could be power from the FACP itself, a horn and strobe power supply for a Notification Appliance Circuit (NAC), or a Fire Rated Auxiliary Power Supply.
Using an input module, the voltage at the control relay that is installed by the sound board for sound shutdown also has to be monitored to make sure the power doesn't get disconnected or turned off.
As a power source for the shutdown, the best thing to use is the auxiliary power supply output terminals on the Fire Alarm Control Panel. Second choice would be the auxiliary power supply output terminals on the Booster Power Supply (or Signal Power Expander, or whatever the manufacturer calls the box that provides extra power to the Notification Appliance Circuit of NAC).
However, if the wires are already buried in the walls and ceilings, and an extra power supply wire can't be run all the way from the Fire Alarm Control Panel, a fire rated 12 or 24 volt, battery backed up power supply will have to be installed.
One thing about the added fire rated power supply. Don't forget to us an input module on the SLC to monitor the trouble contacts on the added power supply. That way if anything happens like a battery going bad, the troubles on the power supply can be sent back to the Fire Alarm Control Panel, and then the problem can be fixed.
Notification Appliance Circuit (NAC)The NAC is a bad choice for the sound shutdown signal because connecting the sound system shutdown to the Notification Appliance Circuit (NAC) destroys the Class B or Class A status of the horn and strobe (NAC) circuit.
If there is a fire and the fire alarm panel is silenced but not reset, another problem is that using the NAC as a signal source will allow the auditorium sound control board to automatically reactivate the normal sound reinforcement. This could indicate to those on stage and those in the audience that everything is OK, when it's not.
Service After the SaleAlso keep in mind, to the technicians working on the system at a later time, your using the NAC as sound shutdown signal source won't be intuitive. For many years to come, fire alarm service technicians may be calling on you to help them figure out problems with sound shutdown.
Ok thanks so much for the valuable info you have sent me!! I really appreciate it!! I plan on furthering my education on fire alarm and get my NICET!! Now I just need to start looking on how to get the study material for that!!
Have a great rest of your weekend!!
How Does the Fire Panel Know Addressable Detectors are OK? -- It's assumed that fire alarm systems have to work all the time because fires happen anytime, but, then again, this is the real world. Problems with... Read More
Just What Is a Signaling Line Circuit (SLC)? -- The SLC (Signaling Line Circuit) is another way of saying Data and Power Circuit. Along with added power to run the sub-computers and their input and output circuits, it's a computer data-buss ... Read More
Why Can't a 70 Volt Speaker be Used With a Fire Alarm System? -- When the fire alarm system is active and is being used for EVAC or voice, there is no difference between the speaker audio used... Read More
What are the Signals on the SLC? -- I would like to know what type of signal is there between addressable fire detectors and the fire alarm monitoring panel. Actually I want to know how the address / location of... Read More